|
Day 1 – June 15, 2010
Table-Top Exhibition
from 8:00 to 17:30 |
|
8:00 – 8:30 |
Continental breakfast |
|
|
Session 1: Development status (chair:
Matthew Trexler) |
|
8:30 – 8:45 |
Welcoming remarks |
|
8:45 – 9:15 |
Cold
Spray: From Initial Concept to a Successful Coating
Process
Dr. Eric Irissou, National Research Council
|
|
9:15 – 9:45 |
Extending
Impact Conditions in Cold Spraying
Dr. Thomas Klassen, University of the Federal Armed
Forces, Germany |
|
9:45 – 10:15 |
Cold Spray Development and Applications at the
University of Ottawa Cold Spray Lab
Dr. Bertrand Jodoin, University of Ottawa |
|
10:15 – 10:45 |
Break |
|
|
Session 2: Fundamentals I (chair: Mahnaz
Jahedi) |
|
10:45 – 11:15 |
A
Socratic Approach to Cold Spray
Dr. Michel Jeandin, MINES ParisTech, France |
|
11:15 – 11:45 |
Particle Consolidation by Low Pressure Cold Spray:
Modelling, Experiments and Applications
Dr. Dmitry Dzhurinskiy, University of Windsor |
|
11:45 – 12:15 |
Interfacial heating during low-pressure cold-gas dynamic
spraying of aluminum coatings
Dr. André McDonald, University of Alberta |
|
12:15 – 13:45 |
Lunch at Le Biftèque : Sponsored by Tecnar Automation
|
|
|
Session 3: Cold spray equipment (chair: Basil
Marple) |
|
13:45 – 14:10 |
Plasma
Giken and the Current State of Cold Spray Technology in
Japan
Mr. Tark
Inukai, Plasma Giken, Japan |
|
14:10 – 14:35 |
COLD
SPRAYING at CGT: a story of success for the past ten
years and the future
Mr. Helmut Höll, CGT, Germany |
|
14:35 – 15:00 |
CENTERLINE-SST Cold Spray Technology and Applications
Dr. Julio Villafuerte, Centerline(Windsor)
|
|
15:00 – 15:20 |
Cold
Particles Characterization Techniques Applied to the
Cold Spray Process
Mr. Luc Pouliot, Tecnar Automation |
|
15:20 – 15:40 |
Characterization and Performance Evaluation of a Helium
Recovery System Designed for Cold Spraying
Mr. Sylvain Desaulniers, Polycontrols |
|
15:40 – 17:30 |
Break |
|
15:40 – 17:30 |
Poster session / cold spray laboratory visit |
|
17:30 – 23:00 |
Diner cruise banquet : Sponsored by University of Ottawa |
|
Day 2 – June 16, 2010
Table-Top Exhibition
from 8:00 to 17:00 |
|
8:00 – 8:30 |
Continental breakfast |
|
|
Session 4: Characterization (chair:
Thomas Klassen) |
|
8:30 – 9:00 |
Amorphous Coatings Produced by Cold Spray
Dr. Leonardo Ajdelsztajn, General Electric – Global
Research Center , USA |
|
9:00 – 9:30 |
Electron
Microscope Observations of Cold Sprayed Coatings
Dr. Stephen Yue, McGill University |
|
9:30 – 10:00 |
Micro-
and Nano-mechanical Testing Techniques Applied to Cold
Sprayed Coatings and Splats
Dr. Richard Chromik, McGill University |
|
10:00 - 10:30 |
Break |
|
|
Session 5: Fundamentals II (chair: Michel
Jeandin) |
|
10:30 – 11:00 |
Fundamental Studies of Cold Spray Titanium
Dr. Mahnaz Jahedi, CSIRO, Australia |
|
11:00 – 11:30 |
Improvement
on Downstream Cold Spray System and Innovative Nozzles
Dr. Lijue Xue, National Research Council |
|
11:30 – 12:00 |
CFD Modeling and Flow Visualization in Cold Spray
Process
Dr. Ali Dolatabadi, Concordia University |
|
12:00 – 13:30 |
Lunch at Le Biftèque |
|
|
Session 6: Applications / case study I (chair:
David Wright) |
|
13:30 – 14:00 |
Cold
Spray Technology Applications
Mr. Matthew Trexler, Army Research Lab, USA |
|
14:00 – 14:30 |
Cold Spray
Nanostructured Aluminum for Corrosion Protection
Dr. George E. Kim, Perpetual technologies |
|
14:30 – 15:00 |
On Cold
Kinetic Spraying of Hydroxyapatite and TiO2 Bioceramics
onto Ti-6Al-4V and Glass Substrates
Dr. K. A. Khor, Nanyang Technological University,
Singapore |
|
15:00 – 15:30 |
Break |
|
|
Session 7: Applications / case study II
(chair: Christian Moreau) |
|
15:30 – 16:00 |
Peculiarities of the Gas Dynamic Spray Applications in
Russia
Dr. Alexander Shkodkin, OCPS, Russia |
|
16:00 – 16:30 |
Practical
Applications of Cold Gas-Dynamic Spray
Mr. David Wright, Accuwright Industries, USA |
|
16:30 – 17:00 |
Cold Spray Corrosion Mitigation for Nuclear Reactor
Mr. Edward C. Malisson, CenterLine
SST |
|
17:00 – 17:15 |
Closing remarks |
